diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index dde4988..6d2609c 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -30,6 +30,8 @@
 #include <phy.h>
 #include <input.h>
 #include <i2c.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -51,8 +53,11 @@
 #define USDHC1_CD_GPIO		IMX_GPIO_NR(1, 2)
 #define USDHC3_CD_GPIO		IMX_GPIO_NR(3, 9)
 #define ETH_PHY_RESET		IMX_GPIO_NR(3, 29)
+#define ETH_PHY_AR8035_POWER	IMX_GPIO_NR(7, 13)
 #define REV_DETECTION		IMX_GPIO_NR(2, 28)
 
+static bool with_pmic;
+
 int dram_init(void)
 {
 	gd->ram_size = imx_ddr_size();
@@ -107,6 +112,11 @@
 	IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 };
 
+static iomux_v3_cfg_t const enet_ar8035_power_pads[] = {
+	/* AR8035 POWER */
+	IOMUX_PADS(PAD_GPIO_18__GPIO7_IO13    | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
 static iomux_v3_cfg_t const rev_detection_pad[] = {
 	IOMUX_PADS(PAD_EIM_EB0__GPIO2_IO28  | MUX_PAD_CTRL(NO_PAD_CTRL)),
 };
@@ -120,6 +130,14 @@
 {
 	SETUP_IOMUX_PADS(enet_pads);
 
+	if (with_pmic) {
+		SETUP_IOMUX_PADS(enet_ar8035_power_pads);
+		/* enable AR8035 POWER */
+		gpio_direction_output(ETH_PHY_AR8035_POWER, 0);
+	}
+	/* wait until 3.3V of PHY and clock become stable */
+	mdelay(10);
+
 	/* Reset AR8031 PHY */
 	gpio_direction_output(ETH_PHY_RESET, 0);
 	mdelay(10);
@@ -192,6 +210,7 @@
 static int ar8031_phy_fixup(struct phy_device *phydev)
 {
 	unsigned short val;
+	int mask;
 
 	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
 	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
@@ -199,7 +218,12 @@
 	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 
 	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
-	val &= 0xffe3;
+	if (with_pmic)
+		mask = 0xffe7;	/* AR8035 */
+	else
+		mask = 0xffe3;	/* AR8031 */
+
+	val &= mask;
 	val |= 0x18;
 	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 
@@ -257,6 +281,40 @@
 	}
 };
 
+struct i2c_pads_info mx6q_i2c3_pad_info = {
+	.scl = {
+		.i2c_mode = MX6Q_PAD_GPIO_5__I2C3_SCL
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6Q_PAD_GPIO_5__GPIO1_IO05
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6Q_PAD_GPIO_16__I2C3_SDA
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6Q_PAD_GPIO_16__GPIO7_IO11
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(7, 11)
+	}
+};
+
+struct i2c_pads_info mx6dl_i2c3_pad_info = {
+	.scl = {
+		.i2c_mode = MX6DL_PAD_GPIO_5__I2C3_SCL
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6DL_PAD_GPIO_5__GPIO1_IO05
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6DL_PAD_GPIO_16__I2C3_SDA
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6DL_PAD_GPIO_16__GPIO7_IO11
+			| MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(7, 11)
+	}
+};
+
 static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
 	IOMUX_PADS(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK),
 	IOMUX_PADS(PAD_DI0_PIN2__IPU1_DI0_PIN02), /* HSync */
@@ -385,6 +443,31 @@
 	return 0;
 }
 
+#define PMIC_I2C_BUS		2
+
+int power_init_board(void)
+{
+	struct pmic *p;
+	u32 reg;
+
+	/* configure PFUZE100 PMIC */
+	power_pfuze100_init(PMIC_I2C_BUS);
+	p = pmic_get("PFUZE100");
+	if (p && !pmic_probe(p)) {
+		pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+		printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+		with_pmic = true;
+
+		/* Set VGEN2 to 1.5V and enable */
+		pmic_reg_read(p, PFUZE100_VGEN2VOL, &reg);
+		reg &= ~(LDO_VOL_MASK);
+		reg |= (LDOA_1_50V | (1 << (LDO_EN)));
+		pmic_reg_write(p, PFUZE100_VGEN2VOL, reg);
+	}
+
+	return 0;
+}
+
 /*
  * Do not overwrite the console
  * Use always serial for U-Boot console
@@ -414,6 +497,14 @@
 		return false;
 }
 
+static bool is_revd1(void)
+{
+	if (with_pmic)
+		return true;
+	else
+		return false;
+}
+
 int board_late_init(void)
 {
 #ifdef CONFIG_CMD_BMODE
@@ -426,7 +517,9 @@
 	else
 		env_set("board_rev", "MX6DL");
 
-	if (is_revc1())
+	if (is_revd1())
+		env_set("board_name", "D1");
+	else if (is_revc1())
 		env_set("board_name", "C1");
 	else
 		env_set("board_name", "B1");
@@ -441,10 +534,13 @@
 
 #if defined(CONFIG_VIDEO_IPUV3)
 	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
-	if (is_mx6dq())
+	if (is_mx6dq()) {
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c2_pad_info);
-	else
+		setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c3_pad_info);
+	} else {
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
+		setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c3_pad_info);
+	}
 
 	setup_display();
 #endif
@@ -454,7 +550,9 @@
 
 int checkboard(void)
 {
-	if (is_revc1())
+	if (is_revd1())
+		puts("Board: Wandboard rev D1\n");
+	else if (is_revc1())
 		puts("Board: Wandboard rev C1\n");
 	else
 		puts("Board: Wandboard rev B1\n");
diff --git a/configs/wandboard_defconfig b/configs/wandboard_defconfig
index 72ff721..e12f870 100644
--- a/configs/wandboard_defconfig
+++ b/configs/wandboard_defconfig
@@ -15,6 +15,7 @@
 # CONFIG_CONSOLE_MUX is not set
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+# CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_SPL=y
 CONFIG_SPL_EXT_SUPPORT=y
diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index 3ba4c29..ba88d02 100644
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -13,6 +13,7 @@
 #include "mx6_common.h"
 
 #include "imx6_spl.h"
+#define CONFIG_DISPLAY_BOARDINFO_LATE
 
 #define CONFIG_MACH_TYPE		MACH_TYPE_WANDBOARD_IMX6
 
@@ -44,6 +45,12 @@
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED		100000
 
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
 /* MMC Configuration */
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
@@ -102,6 +109,10 @@
 			"fi; "	\
 		"fi\0" \
 	"findfdt="\
+		"if test $board_name = D1 && test $board_rev = MX6Q ; then " \
+			"setenv fdtfile imx6q-wandboard-revd1.dtb; fi; " \
+		"if test $board_name = D1 && test $board_rev = MX6DL ; then " \
+			"setenv fdtfile imx6dl-wandboard-revd1.dtb; fi; " \
 		"if test $board_name = C1 && test $board_rev = MX6Q ; then " \
 			"setenv fdtfile imx6q-wandboard.dtb; fi; " \
 		"if test $board_name = C1 && test $board_rev = MX6DL ; then " \